New Page 1

ULTIMA-TIG: for eco friendly electrode grinding and optimal TIG-welding guaranteed.

Eco friendly collection of toxic dust particles Perfect grinding for accurate angles A combined electrode length gauge and locking device, ensuring minimal removal of electrode during grinding(0.3mm) polished angle surface for easier arc striking and arc stability Longer electrode life between regrinds

BH Tungsten Grinders and the patented wet grinder ULTIMA-TIG demonstrate an eco friendly way to perfect accurate angles on tungsten electrodes – and therefore perfect TIG-welding.

ULTIMA-TIG is constructed with a unique disposal container that automatically collects all toxic dust particles, eliminating the need for separate exhaust systems. The container can be disposed of via your distributor or BH Tungsten Grinders.

Cold wet grinding combined with the diamond wheels high grinding speed ensures that the tungsten electrode always has a polished and even surface.

With ULTIMA-TIG you will achieve the exact angle that you require. A special locking device positions the electrode precisely, and the grinding is carried out in the correct longitudinal direction along the electrode. A precise angle is not only important to the quality of the welding seams but it increases the number of re-ignitions between grinding. Thus prolonging the electrode life.

ULTIMA-TIG is easy to use. Place the electrode in the electrode holder. Adjust the pointer to the required grinding angle and insert the tungsten electrode into the combined stick-out and locking device. After the grinding has taken place you can, if needed, flatten the tip by placing the electrode clamp in the 90 degree position.

ULTIMA-TIG is available in 220V and 110V and comes complete with a 2 metre cable, 250ml bottle of grinding liquid, diamond wheel, electrode clamps (1.6mm-3.2mm), electrode holder, disposable container complete with liquid and a stainless steel stand. ULTIMA-TIG is CE marked and meets all current EU regulations.

Motor: 110/220V, 50/60Hz
Motor yield: 380W
Rpm: 8500/min
Grinding speed: 44 m/sec.

NEUTRIX: Portable grinding machine for Tungsten electrodes

Integrated exhaustion with a replaceable dust filter Triple use of the diamond wheel Easy to use, combined electrode positioning and locking devise Grinding electrode as short as 8mm

BH Tungsten Grinders has, with the development of NEUTRIX* produced a portable Tungsten grinder, that is both environmentally friendly and able to grind quality points on Tungsten electrodes for TIG and plasma welding.

The storage case along with the moderate weight make NEUTRIX ideal for working on site.

Neutrix is the only machine that is equipped with an integrated dust filter, thereby protecting the operator and the environment against the unhealthy dust produced during grinding of the electrode. The filter is replaceable.

Due to the use of an electrode holder NEUTRIX is able to grind electrodes as short as 15mm with a standard electrode clamp, with a special electrode clamp as short as 8mm can be ground. The use of the electrode holder also ensure a precise and centred tip.

Neutrix is equipped with an inspection cover enabling the operator to see the grinding operation. Neutrix is easy to operate, set the required grinding angle, secure the electrode into the holder using the locking device. The electrode is now set so as to minimise the amount of grinding required (0.3mm removal).

As something quite unique NEUTRIX is equipped with an eccentric plate, which makes it possible to adjust the grinding position on the face of the wheel, this triples the life of the diamond wheel.

NEUTRIX is supplied in a case fully equipped for use, electrode clamps for 1.6, 2.4 and 3.2 diameter tungstens are included, other sizes are available. NEUTRIX is CE marked and is manufactured to meet all EU directives.

Power Supply: 110/230V
Motor: 850W
Rpm: 28000
Weight: 2.8 kg

BYMAT (1024 RS) - Stainless Steel Cleaners


5 applications in one unit:
Cleaning Electropolishing Light marking Dark marking Electroplating

The most up-to-date technology and an impressive process permit a completely new method for cleaning welded seams, which puts an end to the disadvantages of mechanical or chemical processes and replaces them by an electrolytic process. This all takes place in the workshop simply, cost-effectively and cleanly. It is not harmful to man and is environmentally and product-friendly. The user-friendly 3-way switch supplies the necessary current: Cleaning / embossing dark (alternating current /AC) Polishing / embossing light (direct current/DC+) Electroplating / metal plating (direct current/DC-) The voltage regulation takes place variably via a rotary switch.

The whole set of accessories fits into one case and thereby holds everything that is needed for success.

The cleaning of welded seams on stainless steel components.

The oxide film is easily removed and the undesirable tarnish disappears, there are no unsightly edge marks – and this alone has always required a further work step. The surface is simultaneously protected from corrosion (passivated). In comparison with cleaning and pickling with acids this process is significantly cheaper. The chemicals used for the process contain no hazardous substances and are not subject to the duty of marking.

Electropolishing

The grey edge marks (heat-affected zones) close to the welded seams caused by the material changes during welding can be removed without any problem. It is possible to polish stainless steel to a high gloss thus creating a uniform surface even in the case of a 3D-reflective material.

Dark marking of electrically - conductive surfaces

Marks even cylindrical components deep black, easily, rapidly and cheaply. Because of the short reaction time of an electrolyte in connection with a template made according to your own requirements, graphics, trade marks, type plates, device numbers, identification numbers, scales, texts and logos can be permanently marked. Our high-performance electrolyte is neutral (ph 7) and requires no neutralization.

Light marking of electrically - conductive surfaces

By means of material removal in connection with a template made according to your own requirements, we achieve a light marking effect similar to engraving. This is suitable for black steels and aluminium for examples.

Electroplating / metal plating

With this process it is possible to precipitate electrolytically every material which can be liquefied. For examples zinc-plating as corrosion protection. Furthermore the welded seams can be after treated on zinc-plated components. Possible metal coatings: Tin, Zinc, Gold, Silver, Nickel, Chrome, Cadmium, Cobalt, Copper, Brass.

Technical data:

Voltage:
Primary: 110/230 Volt, 50 -60 Hz Secondary: 0 - 24 Volt 0-16 Ampere, 50 Hz
Dimensions:
Width x Height x Depth:143 x 300 x *380 mm
*(Connector cable not included)

BYMAT (1124 RE) - Stainless Steel Cleaners


3 applications in one unit:

Cleaning: The BYMAT 1124 RS is an appliance for electrochemical cleaning of weld seems on VA steel. The fluid used is more over completely safe and environment-friendly. Electropolishing: Grey edges (heat-affected zones) can be straight forwardly removed. In this way high-grade steel can be polished to a high mirror finish. Dark marking: Marks easily, quickly and inexpensively - jet black even on cylindrical components.

Technical data:

Voltage:
Primary: 110/230 Volt, 50 -60 Hz Secondary: 0 - 24 Volt 0-12 Ampere, 50 Hz
Dimensions:
Width x Height x Depth:150 x 290 x 300 mm

BYMAT (RS 924) - Stainless Steel Cleaners


2 applications in one unit:

Cleaning: The BYMAT 924 RS is an appliance for electrochemical cleaning of weld seams on stainless steels. The fluid used is completely safe and environmentally friendly. Electro polishing: Grey edges (heat-affected zones) can be easily removed. In this way high-grade steel can be polished to a high mirror finish.

Technical data:

Voltage:
Primary: 110/230 Volt, 50 -60 Hz Secondary: 0 - 24 Volt 6.3 Ampere 50 Hz
Dimensions:
Width x Height x Depth:125 x 225 x 275 mm